During this period of time, we have pressed a lot of consulting float customers, many people are asking how the parade float is made, how it is designed, how it is made, in the face of these problems that everyone is concerned about, today Jinhui lights to tell you, and do one by one answer, parade float is also what we usually call parade float, is now a large festival activities, Corporate promotion or a variety of opening celebrations in the more commonly used cultural performance activities, the float has its greater influence, publicity, atmosphere set off, has been adopted by businesses, and held a variety of float parade activities. A good parade float is hard-won, it integrates everyone's creativity, planning, design is the crystallization of the wisdom of all staff. Before we do the float, we must first determine the theme of the float, we must have a clear direction, plan around the theme of the float, innovate, and design a rendering, and consider the structure of the float in all aspects when making the drawing, the size of the float, which model is selected to do the carrier and so on.
Wire, Yuan bar, Angle iron, satin, LED lighting
Welding machine, electric drill, air compressor
After determining the plan, we have to choose the truck according to the size of the actual production of the lights, most of the cruise float use time is short, the general cycle is only a few hours to a few days, in this case, we can rent the truck to make the float, when renting the truck to a single row of trucks is more appropriate, if the float is 6 to 8 meters long, Then we can choose 4 meters to 5 meters of trucks, if the parade float is made to 10 meters to 12 meters long, we can choose 8 meters long trucks. Select the right truck according to the length of the parade float. Of course, we sometimes use a special battery car frame to make floats.
After the artist lofting, the float scheme is determined, we will start to make the float, first of all, the first step we have to do is by the artist lofting, the float on the components according to the construction drawing of the sample 1:1 size on the ground, requiring the positive sample and side sample at the same time. Smooth lines and even thickness.
Fitter sampling and welding, by our light production technician according to the lofting drawing sampling, sample drawing we choose 8 to 12 iron wire sampling production. Large shape components we use No. 6 straight element and welded forming, hardness is not enough we also use Angle iron to do internal support, through welding processing a piece of the skeleton of the light component is produced.
Silk rack anti-rust treatment. We use special anti-rust paint for anti-rust treatment of the wire frame, and spray the anti-rust material evenly on each iron wire with an air compressor, and check it several times to do not miss a solder joint.
Float assembly lights, after anti-rust treatment of the skeleton lights, light source we choose special energy-saving LED lights, lights can not be installed into the place, we use LED soft light strip to achieve lighting effect. We also pay attention to the installation of lights, as far as possible in the position of the wire frame, and require the lamp position to be uniform, as far as possible not to show the shadow of the skeleton, to achieve the lighting effect of light without showing the light point. Choose the appropriate light source according to different silk fabrics. After the light position is set, we should test the power to make sure that every bulb is lit.
Float components package, we in accordance with the requirements of the diagram on each piece of float components, with cloth strips to table color cloth set, as a color label, pasting workers will be mounted on the silk cloth on the wire frame, to achieve flat, straightened, trim to tidy, after the component mounted we want to the intersection of the color cloth with golden gold edge decoration. 7, the float spray color treatment, pasted the components, according to the requirements of senior artists to handle the color, manual painting, drawing the required color and pattern.
Float shelf production, in order to make the good components installed on the float, we also have to level the truck, do the base, and the front of the package decoration, in the front welding, we have to be particularly careful, to prevent the car glass damage, to protect the car glass, with the carpet wrapped in the car glass, and all wet with water, to prevent the welding flying welding flower damage ring glass.
Float assembly, which is the last step of the float process, will do a good job of the parts, there is an orderly assembly up, and the assembly is bound and welded, and it is required to install firmly, and it will not fall or fall apart when cruising. After all the parts are installed, we have to attach a skirt around the float for a week. A parade float like this is finished.